TIGONIS Super Power SBR Latex

If using this product as a cementitious bond coat, the base concrete must be a minimum of 3 days old. The concrete must be clean and all oil, dirt, debris, paint, curing compounds, sealers and unsound concrete must be removed. The surface must be prepared mechanically using a scabbler, bush hammer, shot blaster or scarifier, so that the minimum surface profile is 3 mm and exposes the large aggregate of the concrete.

► Waterproofing of roof slabs/columns/sunshades/sunken slabs, basements/water tanks/waterproofing of bathroom, toilet/terraces, etc. in combination with cement.
► Increased bonding agent for uses in crack repair and plastering.
► Treatment for leaching and saltpetre action.
► Excellent coverage, economic – approx 60-80 sq ft per kg/two coats (mix 1:4:7 – TSPLA: Water: Cement) TSPLA can be diluted with water (1:4-6) depending on the type of application.

1 – Waterproof Slurry Coating/Bond Coat Mixing Ration-TSPLA*:Water: Cement = 1:4:7-9(by Weight)

2 – Polymer Repair Mortar (1 Cement:4 Sand) Liquid Mixing Ratio-TSPLA*:Water =1:6 | Liquid : Powder ratio = 1:2

3 – Crack filling Putty (1 Liquid 2 Marble Dust) Liquid Mixing Ratio – TSPLA*: Water =1:2

4 – Polymer Concrete (Repair Concrete & Screed) (1 Cement:2 stand:4 Aggregates) Liquid Mixing Ratio: TSPLA*: Water = 1:4 | Liquid Powder ratio =1:2

5 – Additive to cement for injection grouting Liquid Mixing Ratio: TSPLA*: Water=1:5; Liquid:Cement =1:2

Prepare the base as per direction. Spread cement primer by Using TSPLA*: Water=1:4 by volume in order to obtain a thin layer. When the primer coat is still fresh and sticky, apply mortar made out of TSPL*: Water=1:4 by volume and finish with a trowel/brush. During application continue stirring the mixture of TSPLA* and cement. Prepared material must be used within 20-30 minutes depending upon temperature humidity etc. when used as waterproofing slurry coating minimum two coats is recomended.

Prepare the base as directed. Make a firm mortar with fine sand using TSPLA*: Water = 1:6-8. Apply primer coat as above. While the Primer is still wet, apply the mortar and immediately finish.

01) Store in well ambient conditions, ventilated locations & away from sources of ignition and fire.
02) Keep away from children.
03) In case of eye/skin contact, wash with plenty of water.
04) Inhalation / Injection is dangerous. In either case, move to fresh air & consult a medical practitioner.
05) Do not apply when the ambient temperature might drop to a level below 10^C within 4 hrs of application.
06) New plaster should be allowed to cure for a minimum of 12 weeks.
07) Avoid extra thinning for better results.
08) Can be tinted with Universal Stainer before thinning. Do not add more than 5%
Universal Stainer. Stir the tinted paint well, after tinting & before application.
09) The container must be tightly closed when not in use. Stir well and strain before use.
10) Use safety equipment like rubber or polythene gloves, safety goggles/glasses & face mask.

Dilute TSPLA* with water in the proportion of 1:6 by volume. Prepare the mortar with this mixed water. This type of polymer mortar should be used for all repair jobs for optimum performance.

Non-Flammable.

As waterproof coating 2-6 hours depending on the temperature and humidity.

For waterproofing or damp proofing application, always use at least 2 coats. In areas of serve water penetration, three coats might be required.

3-5 days with wet burlap/gunny bag/hessian cloth. Not to be ponded with water.

Clean tools and equipment with water before the material hardens. Use rubber hand gloves and safety goggles while using TSPLA* In case of skin Contact, wash with plenty of water. Keep out of reach of children.